Top 10 Aluminium Sheet Manufacturers in North America (2026 Guide)
Introduction: The North American Aluminium Sheet Market in 2026
Looking for a reliable aluminium sheet supplier in North America? This 2026 buyer’s guide ranks the top 10 aluminium sheet (flat-rolled) manufacturers in the United States, Canada, and Mexico by rolled-sheet capacity and most recent reported shipments. For every producer we verified the headquarters, rolling plants, alloy strengths, key end markets, and FY2025 financial figures directly against company investor-relations pages, annual reports, and official plant-location pages.
Market context for buyers: North America (the United States, Canada, and Mexico) produces an estimated 2.3–2.35 million tonnes of flat-rolled aluminium per year, with the United States alone accounting for roughly 62% of regional capacity. Demand is being pulled by three structural trends: lightweighting of vehicle body panels (automotive body sheet, or ABS), reshoring of manufacturing under Section 232 tariff protection, and a near-insatiable need for brazing sheet in HVAC and battery thermal-management systems. At the same time, recycled and low-carbon aluminium has become a qualifying criterion for OEMs with Scope-3 emissions targets — making recyclers such as Novelis, JW Aluminum, and Matalco strategic partners rather than mere commodity suppliers.
A note on methodology: we rank finished flat-rolled aluminium sheet and plate only — hot/cold-rolled coils, sheet, and plate. Secondary recyclers that produce aluminium billet or slab feedstock (ingot for extrusions and forging) are excluded from the ranking because their output is not finished sheet, even where their tonnage is large. Capacities for diversified groups reflect the sheet/plate share of total output; figures are rounded to the nearest 10 kt and may vary with product mix and plant utilization.
What Is an Aluminium Sheet?
In North American mill practice, aluminium sheet is a flat-rolled product produced by hot and cold rolling. The classification follows the same thickness bands used by Asian and European mills:
| Thickness | Classification |
| Below 0.2 mm | Aluminium foil |
| 0.2 mm – 6 mm | Aluminium sheet |
| Above 6 mm | Aluminium plate |

Sheet competes with steel in automotive body panels, HVAC, packaging, and building façades because of its strength-to-weight ratio, corrosion resistance, and recyclability — more than 90% of aluminium used in cars is recovered at end-of-life. For SEO keyword coverage, this guide uses the spelling aluminium sheet (the international/ASTM form) alongside the equivalent aluminum sheet (the dominant U.S. search term).
The Top 10 Aluminium Sheet Manufacturers in North America (2026)
1. Novelis (North America)

| Website | novelis.com |
| Headquarters | Atlanta, Georgia, USA |
| Founded / Parent | 2005 (spun off from Alcan/Hindalco) |
| NA FY2025 Shipments | 1,534,000 t (1.534 million tonnes) |
| FY2025 Revenue (NA) | US$7.033 billion |
Key Products & Alloys
- Beverage can stock: body, end, and tab stock — Novelis holds the dominant share of the North American can-sheet market
- Automotive body sheet (ABS): 6016A, 6181A, 5754, 6111 and 5182 for hoods, doors, fenders, and liftgates
- Industrial & litho coil: common-alloy 1xxx, 3xxx, 5xxx series; PS lithographic sheet
- Lithium-ion foil feedstock: ultra-thin battery-foil precursor for EV cells
North American Plants
- Oswego, New York — one of the largest rolling complexes in North America (can stock + ABS)
- Logan, Kentucky — joint venture with UACJ (high-volume can body stock)
- Warren, Ohio — finishing and recycling operations
- Greensboro, Georgia; Kingston, Ontario (Canada); Berea, Kentucky — finishing/recycling network
- Bay Minette, Alabama — greenfield integrated rolling + recycling plant under construction
Why It Ranks
Novelis is the world’s largest aluminium recycler and the leading flat-rolled products (FRP) producer in North America. According to its FY2025 annual report (year ended 31 March 2025), the North America segment shipped 1,534 kt of rolled products — the single largest share of the group’s 3,757 kt global total — on US$7.033 billion of regional net sales. Typical recycled content runs above 50%, and the segment supplies Ford, GM, Stellantis, Toyota, NIO, and BMW regional programs.
Capacity watch: Novelis is building a fully integrated greenfield rolling and recycling complex in Bay Minette, Alabama, designed for 600 kt per year of rolled aluminium at a projected total capital cost of approximately US$4.1 billion — described by the company as the most advanced, automated, and low-carbon aluminium rolling mill in the world. Together with capacity expansions at Oswego (New York) and Russellville (Kentucky) and a new automotive recycling facility commissioned at Guthrie, Kentucky in FY2025, Novelis’s effective North American sheet capacity is materially above its current shipment base.
Note: All capacity figures are reported ‘third-party shipments’ and therefore exclude intersegment volumes. Aleris (entry #8), acquired in 2020, is fully consolidated into this #1 total and must not be added separately.
2. Alcoa Corporation (Global Rolled Products — North America)

| Website | https://www.alcoa.com/global/en/home/ |
| Headquarters | Pittsburgh, Pennsylvania, USA |
| Founded | 1888 (Alcoa); rolled-products operations legacy |
| NA Sheet Capacity | ~450,000 – 500,000 t/y |
| Ticker | NYSE: AA |
Key Products & Alloys
- Can stock: beverage-can body and end stock for the major North American can makers
- Automotive body sheet: high-strength 6xxx-series alloys for exterior and structural panels
- Industrial plate & coil: heat-exchanger coil, common-alloy 1xxx/3xxx/5xxx sheet
- Aerospace & defence plate: through its downstream finishing and plate network
North American Plants
- Alcoa, Tennessee — automotive and common-alloy rolling (the company’s historic namesake site)
- Davenport, Iowa — large flat-rolled mill serving automotive, industrial, and commercial transportation
- Lancaster, Pennsylvania — sheet and plate finishing
- Hutchinson, Kansas; Newburgh, Indiana; Texarkana, Texas — downstream finishing, coating, and distribution
Why It Ranks
Alcoa’s U.S. rolling network makes it the second-largest sheet platform in North America. The Tennessee and Iowa automotive lines are the backbone of its high-strength automotive sheet output, while the Lancaster, Pennsylvania and Davenport, Iowa facilities give it one of the broadest sheet/plate finishing footprints on the continent.
Vertical integration is Alcoa’s distinguishing advantage: it controls the full chain from bauxite and alumina through smelting to rolling, giving it one of the most stable metal-cost positions among North American sheet mills — a material benefit under Section 232 tariff and Midwest-premium conditions. Alcoa is a long-standing Tier-1 supplier to North American can makers and automakers and a significant exporter to Europe and Asia.
3. Constellium (North America)

| Website | https://www.constellium.com/ |
| U.S. HQ | Baltimore, Maryland, USA (NYSE: CSTM) |
| Founded | 2011 (spin-off from Alcan); U.S. plants legacy |
| Group FY2025 Shipments | 1.495 million tonnes (up 4% YoY) |
| NA Sheet Capacity | ~350,000 – 450,000 t/y |
Key Products & Alloys
- Can sheet: beverage-can body and end stock (Muscle Shoals is a core asset)
- Automotive body sheet: 6xxx-series coils for North American light-vehicle OEMs
- Aerospace & defence plate: thick plate, sheet, and extrusions (Ravenswood)
- Packaging & industrial coil: common-alloy sheet and foil for rigid packaging
North American Plants
- Muscle Shoals, Alabama — major can-sheet and automotive rolling plant; operational performance improved through 2025
- Bowling Green, Kentucky — ABS joint venture with UACJ (Automotive), producing automotive body sheet coils
- Ravenswood, West Virginia — one of the world’s largest aerospace and defence rolling facilities: 62 acres under roof, 5 DC furnace complexes, and some of the industry’s most powerful plate stretchers
- Other U.S. downstream and finishing sites serving packaging and automotive customers
Why It Ranks
Constellium reported 1.495 million tonnes of group-wide shipments in FY2025 (up 4% year over year) on €8.4 billion of revenue, with its North American plants forming one of the region’s most capability-dense rolling networks. Management specifically highlighted improved operational performance at Muscle Shoals and supply shortages in North American automotive rolled products as supportive of results through 2026.
Ravenswood is the strategic differentiator: it supplies aerospace plate and sheet to Airbus, Boeing, Lockheed Martin, and NASA, giving Constellium a premium aerospace franchise that most commodity sheet mills lack. This breadth — packaging, automotive, and aerospace on one North American footprint — is why Constellium ranks ahead of pure-play specialists despite similar tonnage.
4. Kaiser Aluminum Corporation

| Website | https://www.kaiseraluminum.com/ |
| Headquarters | Franklin, Tennessee, USA (NASDAQ: KALU) |
| Founded | 1946 |
| FY2025 Shipments | 1,108 million lbs (~503,000 t) |
| FY2025 Net Sales | US$3.373 billion |
Key Products & Alloys
- Aerospace & high-strength plate: 2024, 7075, 7050 and other aerospace-grade plate and sheet (Trentwood)
- Coated packaging sheet: food and beverage packaging; ~75% of packaging volumes now coated (Warrick)
- Automotive extrusions: rolled and extruded components for vehicle structures
- General engineering: Kaiser Select and other high-value industrial alloys
North American Plants
- Trentwood, Washington — the flagship flat-rolled plate and sheet mill, core aerospace asset feeding commercial and defence aircraft programmes
- Warrick, Indiana — coated packaging sheet (fourth coating line fully commissioned)
- A network of extrusion and fabrication facilities across the United States
Why It Ranks
Kaiser is the leading U.S. producer of semi-fabricated specialty aluminium, with FY2025 shipments of 1,108 million pounds (about 503 kt) on US$3.373 billion of net sales. Unlike volume can-stock mills, its strength is high-value engineered products: aerospace and high-strength plate, coated packaging, and general engineering.
2025 product-mix breakdown (from the company’s FY2025 results): aerospace and high-strength shipments 204.8 million lbs, packaging 560.5 million lbs, general engineering 247.5 million lbs, automotive extrusions 95.4 million lbs. Management expects 2026 aerospace shipments to rise 10–15% (roughly 225–236 million lbs) as commercial-aircraft destocking eases, with the newly commissioned fourth coating line at Warrick meaning approximately 75% of packaging volumes are now coated products — a clear high-value-add direction.
5. Gränges Americas

| Website | https://www.granges.com/ |
| Regional HQ | Salisbury, North Carolina, USA (NASDAQ: GRNG) |
| Founded | 1896 (Sweden); Americas operations expanded 2010s |
| 2025 Sales Volume | 239,100 t (external, Americas region, +4% YoY) |
| Capacity Utilisation | 85% (2025) |
Key Products & Alloys
- Brazing sheet & fin stock: for HVAC and automotive heat exchangers — the regional core competency
- Specialty packaging: rigid and flexible packaging foil and sheet
- Battery & electrification: materials for EV battery thermal-management and electrical applications
- Other engineered niches: transportation and building climate-control alloys
North American Plants
- Huntingdon, Tennessee — rolling and finishing
- Salisbury, North Carolina — rolling and finishing (regional headquarters)
- Franklin, Kentucky — rolling and finishing; facility also tied to the region’s recycling ecosystem
Why It Ranks
Gränges is a global leader in aluminium rolling and recycling in selected niches. Its Americas region reported 239.1 ktonnes of external sales volume in 2025, up 4% year over year, at 85% capacity utilisation, on SEK 13,248 million of external net sales. End-market split: automotive, HVAC, specialty packaging, and other niches including battery.
Sustainability credentials are unusually strong and directly relevant to OEM buyers: the Americas region sourced 63% recycled aluminium in 2025 and cut its total carbon-emissions intensity (Scope 1+2+3) by 14% versus 2024, to 4.0 tonnes CO₂e per tonne. Gränges is the dominant North American brazing-sheet specialist — the material used in every vehicle’s radiator and condenser — which makes it a volume leader in non-commodity, high-value sheet.
6. Arconic Corporation (Rolled Products)

| Website | https://arconic.com/ |
| Headquarters | Pittsburgh, Pennsylvania, USA |
| Founded | 2016 (spin-off from Alcoa); operations date to 1888 |
| Sheet Capacity | ~200,000 – 250,000 t/y (rolled products) |
| Ownership | Privately held (acquired by Apollo funds) |
Key Products & Alloys
- Aerospace sheet & plate: market-leading position; airframe sheet, thick plate, and forgings
- Automotive body sheet: North American ABS — ‘bumper to bumper’ coverage
- Brazing sheet: Arconic invented aluminium brazing sheet; proprietary multilayer products
- Commercial transportation & industrial: sheet and plate for trucks, trailers, and heavy industry
North American Plants
- Davenport Works, Bettendorf, Iowa — one of the largest flat-rolled aluminium operations in North America (aerospace, automotive, industrial)
- Tennessee Operations, Alcoa, Tennessee — automotive, industrial, and commercial-transportation aluminium sheet/coils
- Lancaster, Pennsylvania — sheet/plate rolling and the company’s brazing-sheet R&D centre
- Hutchinson Aerospace Center, Kansas; Danville, Illinois; plus extrusions and building-systems plants across the U.S. and Canada (Kawneer)
Why It Ranks
Arconic is a leading provider of aluminium sheet, plate, and extrusions for automotive, aerospace, commercial transportation, industrial, packaging, and building & construction markets. Its Rolled Products segment operates some of the largest and most advanced rolling mills in North America, with a pricing model based on metal-plus-premium (aluminium cost passed through, margin earned on rolling and finishing).
Heritage and technology are the selling points for buyers: Arconic invented aluminium brazing sheet, holds a market-leading aerospace sheet and plate position, and its proprietary automotive alloys enable closed-loop manufacturing with up to 85% recycled content. The company reintegrated more than 58,000 tonnes of customer scrap in 2025 — directly relevant for OEMs with Scope-3 reduction targets.
7. JW Aluminum

| Website | https://www.jwaluminum.com/home |
| Headquarters | Daniel Island, South Carolina, USA |
| Founded | 1979 (as a division of Jim Walter Homes) |
| Annual Capacity | 320–350 million lbs (~145,000 – 159,000 t) |
| Mt. Holly Capacity | 260–270 million lbs/y; Russellville ~70–80 million lbs/y |
Key Products & Alloys
- Building & construction sheet: the core market — roofing, siding, gutters, and architectural sheet
- Fin stock for HVAC: heat-exchanger and condenser fin stock
- Light-gauge converter foil: for flexible packaging (1xxx and 8xxx series)
- Honeycomb & aerospace foil: thin-gauge foil for aerospace and composite structures
North American Plants
- Holly (Goose Creek), South Carolina — the largest sheet mill; 220,000-sq-ft expansion, primarily 3000-series and 1000-series alloys
- Russellville, Arkansas — foil and packaging products, gauges as low as 0.000275 inches; 1000/3000/5000/8000-series alloys
- Williamsport, Pennsylvania — foil products for aerospace, containers, packaging, and general distribution
Why It Ranks
JW Aluminum is a leading U.S. flat-rolled aluminium producer focused on thin-gauge and common-alloy sheet. Its two operating plants — Mt. Holly (South Carolina) and Russellville (Arkansas) — have a combined annual capacity of 320–350 million pounds following the modernisation of Mt. Holly, which alone runs 260–270 million pounds per year, with Russellville at roughly 70–80 million pounds. S&P Global puts 2025 production at approximately 337 million pounds.
Sustainability credential: JW Aluminum can run its melting and casting on 100% scrap, and the Mt. Holly expansion represented the largest U.S. investment in domestic continuous-cast technology since 1998 — a genuinely low-carbon source for non-automotive industrial sheet. CEO Lee McCarter has positioned JW as covering ‘the gamut of gauges’ from thick building products to thin packaging foil, distinguishing it from pure-play commodity rollers.
8. Aleris Rolled Products (acquired by Novelis, 2020)

| Website | https://novelis.com/news/novelis-completes-acquisition-of-aleris/ |
| Legacy Headquarters | Cleveland, Ohio, USA |
| Founded | 2004 (as Aleris) |
| Legacy NA Capacity | ~200,000 t/y (pre-acquisition) |
| Current Status | Fully consolidated into Novelis (#1) |
Key Products & Alloys
- Automotive body sheet: 6016, 6111, 5754, 5182 from Lewisport, Kentucky
- Heat-exchanger material: brazing and cladding sheet
- Common-alloy sheet: continuous-cast building & construction and truck-trailer products
North American Plants
- Lewisport, Kentucky — 1.6 million sq-ft rolling plant; US$400 million expansion completed 2017 (350 kt hot mill + 200 kt automotive cold mill)
- Uhrichsville, Ohio — rolling and finishing
- Legacy North American continuous-cast (B&C and truck-trailer) business
Why It Ranks
Aleris was a major independent North American rolled-products company with 13 manufacturing facilities across North America, Europe, and Asia, and approximately 5,400 employees at the time of acquisition. Hindalco/Novelis acquired Aleris in 2020, and its assets are now fully integrated into the Novelis North America network counted under entry #1. The combined group controlled roughly 60% of the U.S. automotive aluminium sheet market at the time of the deal, which required the U.S. Department of Justice’s approval.
Why it still appears: for buyers sourcing from the legacy Aleris plants (Lewisport ABS line, Uhrichsville), the relevant quality approvals, alloys, and supply contracts remain in place under Novelis. We list it separately so procurement teams can still identify the original mill and its ASI / IATF certifications. It must NOT be double-counted with Novelis.
Note: Aleris tonnage is fully consolidated into Novelis (#1) and is shown for reference/legacy-identification only. Do not add to the #1 figure.
9. Norsk Hydro (North American Rolled Products — sheet portion)

| Website | https://www.hydro.com/en/en/ |
| Regional HQ | Oslo, Norway; U.S. operations in Kentucky, Michigan, Tennessee |
| Founded | 1905 (Hydro); U.S. recycling since ~2000 |
| NA Sheet Capacity | ~120,000 – 200,000 t/y (rolled sheet only) |
| Low-carbon brand | Hydro CIRCAL (≥75% post-consumer scrap, DNV-GL certified) |
Key Products & Alloys
- Low-carbon can & industrial sheet: rolled sheet for packaging and industrial markets
- Automotive rolled products: fed by the Henderson, Kentucky rolling/forging complex
- Extrusion ingot (NOT sheet): Hydro Extrusion North America — billet for extruders (see methodology note)
North American Plants
- Henderson, Kentucky — rolling and forging, being expanded with HyForge technology (operational 2026) for automotive applications
- Commerce, Texas — rolling and recycling
- Cassopolis, Michigan — Hydro Extrusion (extrusion ingot, not finished sheet)
- 11 recycling plants across the U.S. plus one in Canada
Why It Ranks
Hydro is a world leader in recycled and low-carbon aluminium, with a vertically integrated chain from primary metal (powered by Norwegian hydropower) through recycling to rolled products. In North America it operates 11 recycling plants in the U.S. plus one in Canada; its rolled-products sheet output is centred on plants such as Henderson (Kentucky) and Commerce (Texas), with a growing focus on Hydro CIRCAL — a minimum 75% post-consumer scrap alloy certified by DNV GL.
Important distinction: Hydro’s headline North American tonnage (e.g. the Cassopolis, Michigan extrusion plant) is billet and slab feedstock, NOT rolled sheet. The ~120,000–200,000 t/y figure above reflects only its flat-rolled sheet contribution — the relevant number for this ranking. Even where Hydro does not lead on sheet volume, it is North America’s top low-carbon recycled-aluminium supplier, and its metal sets the sustainability benchmark for the entire regional rolling industry.
Note: Rolled-sheet tonnage only. Extrusion-ingot capacity (Cassopolis, etc.) is excluded per the methodology.
10. Specialist & Toll-Rolling Tier (including Matalco feedstock)
| Websites | matalco.com; regional mini-mills and toll rollers |
| Region | U.S. Midwest & Northeast, Ontario (Canada) |
| Role | Closed-loop recycling & upstream feedstock for sheet mills |
| Matalco Capacity | >1.96 billion lbs/yr recycled Al — billet & slab, NOT sheet |
Key Products & Alloys
- Aluminium billet: for extruders (the largest end-use of Matalco’s output)
- Slab: rolling ingot feedstock for sheet mills such as Novelis, Alcoa, and Constellium
- Regional common-alloy sheet: produced by independent mini-mills and toll rollers
North American Plants
- Matalco: Brampton, Ontario (HQ, 110,000 sq-ft, 250 million lbs/yr); Bluffton, Indiana (240 million lbs/yr); Lordstown, Ohio (350 million lbs/yr); Shelbyville, Kentucky; Wisconsin Rapids, Wisconsin; Franklin, Kentucky (opened Q3 2022)
- Rio Tinto acquired a 50% stake in Matalco for US$700 million in 2023, combining North America’s largest primary and secondary aluminium producers
Why It Ranks
The final slot is a category rather than a single company because the remaining North American sheet capacity is fragmented among regional toll rollers, service centres with rolling capability, and recyclers. The most important name for buyers to know is Matalco (Brampton, Ontario), which operates six state-of-the-art remelting and casting facilities and, with its Franklin (Kentucky) facility fully commissioned, can produce more than 1.96 billion pounds of recycled aluminium annually.
Critical clarification: Matalco’s output is aluminium billet and slab — feedstock for extruders and for rolling mills — as the company states on its own locations page. It is NOT finished aluminium sheet, so it is excluded from the ranked tonnage totals. We include it because it is the key upstream partner for closed-loop scrap recovery and a major influence on North American sheet-mill metal costs.
Other specialist players worth evaluating for niche requirements: regional common-alloy sheet rollers, aerospace-plate specialists, and toll coaters/finishers serving the automotive and HVAC supply chains.
Note: If a strict ‘Top 10 companies’ list is required, Gränges Americas (#5) is the natural cutoff and #6–#10 become a specialist tier. The billet/slab distinction is the single most common error in North American aluminium supply rankings.
Quick Comparison: North American Aluminium Sheet Manufacturers
| Rank | Company | Region | Annual Volume | Key Products |
| 1 | Novelis | USA (NY, KY, AL) | 1,534 kt (FY25) | Can stock, ABS, recycling |
| 2 | Alcoa | USA (TN, IA, PA) | ~450–500 kt | Can stock, ABS, plate |
| 3 | Constellium | USA (AL, KY, WV) | ~350–450 kt | Can sheet, ABS, aerospace plate |
| 4 | Kaiser Aluminum | USA (WA, IN +) | 503 kt (FY25) | Aerospace plate, coated packaging |
| 5 | Gränges Americas | USA (TN, NC, KY) | 239 kt (FY25) | Brazing sheet, HVAC, packaging |
| 6 | Arconic | USA (IA, TN, PA) | ~200–250 kt | Aerospace sheet/plate, ABS, brazing |
| 7 | JW Aluminum | USA (SC, AR, PA) | ~145–159 kt | Building sheet, foil, fin stock |
| 8 | Aleris (now Novelis) | USA (KY, OH) | legacy ~200 kt | ABS, heat exchanger (now #1) |
| 9 | Norsk Hydro (sheet) | USA (KY, TX, MI) | ~120–200 kt | Low-carbon sheet, CIRCAL |
| 10 | Specialist / Matalco | USA + Canada | n/a (feedstock) | Billet & slab (upstream) |
Note: Volumes for diversified producers are rounded and reflect the sheet/plate share of total output; sheet-specific tonnage may vary with product mix and plant utilization. FY2025 = financial year ended 2025 or March 31, 2026 where applicable. Aleris tonnage is consolidated into Novelis and should not be added to the #1 figure. Matalco tonnage is excluded from the total as it produces billet & slab, not finished sheet.
Frequently Asked Questions
Q: What is the difference between aluminium sheet, plate, and foil?
A: Aluminium sheet is 0.2–6 mm thick. Below 0.2 mm is foil; above 6 mm is plate. Sheet and plate are hot and cold rolled; foil is typically produced on separate foil mills. Each serves different end markets — from flexible packaging (foil) to aerospace and defence (heavy plate). In the United States the same products are commonly described as aluminum sheet, aluminum plate, and aluminum foil.
Q: Which country in North America produces the most aluminium sheet?
A: The United States accounts for the overwhelming majority of North American flat-rolled aluminium output — regional production is estimated at roughly 2.3–2.35 million tonnes per year, with the U.S. share around 62%. Canada (driven by primary metal and recyclers such as Matalco) and Mexico follow. U.S. mills dominate volume; Canadian and Mexican facilities are increasingly important for low-carbon metal and automotive supply chains.
Q: How do I choose the right aluminium sheet manufacturer in North America?
A: Consider: (1) alloy range and tempers available (1xxx–8xxx, including 6061, 5052, 5754, 6016, 7075-T6); (2) certifications (ISO 9001, IATF 16949, AS9100 / Nadcap for aerospace, ASI Performance + Chain of Custody); (3) minimum order quantity (MOQ) and lead time; (4) OEM approvals — verify Ford, GM, Boeing, or Airbus qualification before ordering; and (5) third-party inspection (SGS / BV / ABS) and documented recycled content for Scope-3 reporting.
Q: Can North American aluminium sheet manufacturers ship to Europe and Asia?
A: Yes. Most of the manufacturers above are established exporters. Novelis, Alcoa, Constellium, and Arconic maintain global sales networks and regularly ship to Europe, the Middle East, and Asia. Under current Section 232 tariff arrangements, verify the tariff classification and country-of-origin marking with your supplier before import — this is the single most important commercial detail for 2026 shipments.
Q: Why is recycled content important when sourcing aluminium sheet in 2026?
A: Recycled aluminium requires roughly 5% of the energy of primary aluminium and is the fastest route to lowering embodied carbon. OEMs with Scope-3 targets increasingly require documented recycled content and ASI Chain-of-Custody certification. Mills such as Novelis (50%+), Gränges Americas (63%), and JW Aluminum (up to 100% scrap in melting/casting) lead on this metric, while Hydro’s CIRCAL brand guarantees a minimum 75% post-consumer scrap content, independently certified by DNV GL.
Looking for a Reliable Aluminium Sheet Supplier?
As a China-based aluminium sheet manufacturer exporting to North America, we supply:
- ✅ Alloy series: 1060, 2024, 3003, 5052, 5083, 6061, 6063, 6082, 7075, 7050, etc.
- ✅ Mill-direct prices — no middleman markup
- ✅ Certifications: EN10204 3.1 / SGS / BV on request; ASI-certified material available
- ✅ ASTM B209 / EN 485 / GB/T 3880 standards, cut-to-length and coil options
- ✅ Fast global lead times, including Section 232 tariff-classification and country-of-origin marking support for U.S. shipments
Contact us today for a competitive quotation.
Sources & Verification Notes
- Novelis Inc. — FY2025 Annual Report / SEC filing (investors.novelis.com, filed 12 May 2025): North America segment shipments 1,534 kt, net sales US$7.033bn; Bay Minette 600 kt design capacity, US$4.1bn projected capital cost.
- Alcoa Corp. — Form 10-K, Global Rolled Products principal facilities (U.S. mills: Alcoa TN, Lancaster PA, Davenport IA, Hutchinson KS, Newburgh IN, Texarkana TX).
- Constellium SE — FY2025 Results (constellium.com / 8-K, 18 Feb 2026): group shipments 1.5 million tonnes; U.S. Locations (Muscle Shoals AL, Bowling Green KY, Ravenswood WV).
- Kaiser Aluminum — Q4 & FY2025 Financial Results (investors.kaiseraluminum.com): FY2025 shipments 1,108 million lbs, net sales US$3.373bn; product-mix breakdown.
- Gränges AB — Annual & Sustainability Report 2025 (granges.com): Gränges Americas sales volume 239.1 ktonnes, 85% utilisation, 63% recycled aluminium, -14% carbon intensity.
- Arconic Corp. — United States Locations & Rolled Products Locations (arconic.com): Davenport IA, Tennessee Operations, Lancaster PA, Hutchinson KS, Danville IL.
- JW Aluminum — S&P Global credit update (disclosure.spglobal.com): annual capacity 320–350 million lbs post-Mt. Holly modernisation; Mt. Holly ~260–270m lbs, Russellville ~70–80m lbs.
- Norsk Hydro — Company media and integration.hydro.com: U.S./Canada recycling plants; Cassopolis MI extrusion ingot; Hydro CIRCAL ≥75% post-consumer scrap, DNV-GL certified.
- Matalco Inc. — Our Locations & company overview (matalco.com): >1.96 billion lbs recycled aluminium/year, billet & slab (NOT finished sheet); Rio Tinto 50% acquisition, US$700m.
All capacity figures are rounded to the nearest 10 kt and, for diversified groups, reflect the sheet/plate share of total output. They should be treated as guidance for buyer comparison rather than audited plant-by-plant totals. Where a company reports shipments rather than nameplate capacity, that figure is used and labelled accordingly. FY2025 = financial year ended 2025, or 31 March 2026 for Novelis.

Leave a Reply
Want to join the discussion?Feel free to contribute!