7050 Aluminum Alloy: Technical Guide for T6, T7451, and T7651 Conditions
Introduction
7050 aluminum alloy is a third-generation ultra-high strength, heat-treatable Al-Zn-Mg-Cu series aluminum alloy (AA7050/UNS A97050) and the backbone material for critical load-bearing components in aerospace, defense, and high-end industrial manufacturing. Recognized globally for its unique balance of high strength, exceptional fracture toughness, and superior stress corrosion resistance, it dominates applications ranging from aircraft wing spars to landing gear supports—accounting for 65% of the fuselage aluminum used in China’s C919 large passenger jet and widely adopted in Boeing 787 and Airbus A350 programs.
This guide consolidates full-thickness (0.1mm–300mm) technical data, covering chemical composition, mechanical properties across T6/T651/T7451/T7651/T7351/T652 heat treatment states, non-destructive testing standards, machining guidelines, and selection criteria—all aligned with international standards including ASTM, AMS, EN, and AA specifications.
What Is 7050 Aluminum Alloy?
7050 is engineered for extreme performance demands where traditional 7075 alloy falls short. Its core advantages stem from a precisely optimized elemental recipe:
| Element | Role | Content Range |
| Zn | Primary strengthening element; forms nanoscale MgZn₂ (η’) precipitates | 5.7–6.7% |
| Mg | Synergizes with Zn for strength; enhances toughness | 1.9–2.6% |
| Cu | Boosts fatigue resistance and high-temperature stability | 2.0–2.6% |
| Zr | Replaces Cr as a grain refiner; reduces quenching sensitivity and improves thick-section uniformity | 0.08–0.15% |
Unlike 7075, 7050 uses Zr instead of Cr to minimize performance decay in thick sections (>100mm)—making it the only viable choice for large aerospace forgings and heavy-load structures.
Full Thickness & Heat Treatment State Matching
7050 adapts to all product forms (sheet, plate, forging, extrusion) across 0.1mm–300mm thicknesses. Below is the industry-standard selection matrix:
| Thickness Range | Product Form | Recommended State | Typical Applications |
| 0.2–2.0mm | Thin sheet/strip | T6, T651, T7651 | Aircraft skins, fuselage panels, lightweight thin-walled parts |
| 2.0–6.0mm | Rolled sheet | T6, T651, T7651 | Fuselage stringers, wing skins, structural ribs |
| 6.0–25mm | Medium/thick plate | T6, T651, T7451, T7651 | Secondary aircraft load-bearing parts, mold inserts |
| 25–100mm | Thick plate | T651, T7451, T7651, T7351 | Wing spars, fuselage frames, landing gear supports |
| 100–150mm | Extra-thick plate | T7451, T7651, T652 | Large forging billets, heavy-load frames, die bases |
| 150–300mm | Free forgings | T7451, T7651, T652 | Aircraft structural forgings, aero engine casings |
Mechanical Properties by State & Thickness
All data below are synthesized from ASTM B209, AMS 4050/4201, and commercial mill test reports (Southwest Aluminum, Alcoa, Constellium) for engineering design and procurement acceptance.
T7451 (Most Widely Used Aerospace State)
| Thickness (mm) | Tensile Strength (MPa) | Yield Strength (MPa) | Elongation (%) | Hardness (HBW) |
| 0.5–6 | ≥520 | ≥460 | ≥10 | 132–142 |
| 6–25 | ≥515 | ≥455 | ≥10 | 132–142 |
| 25–75 | ≥500 | ≥440 | ≥9 | 130–140 |
| 75–100 | ≥490 | ≥430 | ≥9 | 128–138 |
| 100–150 | ≥480 | ≥420 | ≥8 | 126–136 |
T6/T651 (Peak Strength, Dry Environments Only)
| Thickness (mm) | Tensile Strength (MPa) | Yield Strength (MPa) | Elongation (%) |
| 0.5–6 | ≥560 | ≥500 | ≥7 |
| 25–75 | ≥530 | ≥470 | ≥6 |
| 75–100 | ≥510 | ≥450 | ≥6 |
T7351 (Best Corrosion Resistance, Marine/Offshore Use)
| Thickness (mm) | Tensile Strength (MPa) | Yield Strength (MPa) | Elongation (%) |
| 0.5–6 | ≥500 | ≥440 | ≥11 |
| 25–75 | ≥485 | ≥425 | ≥10 |
Aerospace & Military Compliance Standards
7050 for aviation/military applications must meet strict normative requirements:
- Sheet: AMS 4050 (T7451), AMS 4201 (T7651), ASTM B209
- Forgings: AMS 4107 (T74 die forgings), AMS 4108 (T7452 hand forgings), ASTM A609
- Extrusions: AMS 4340/4341/4342, ASTM B241
- Ultrasonic Flaw Detection: AMS 2632 (plate), AMS 2631 (forging), AMS-STD-2154 (general aerospace)
- Grain Size: ASTM E112, AMS 2315 (aviation grade: ≥Grade 7 for thin plate, ≥Grade 6 for thick plate)
Machining, Welding & Corrosion Resistance Guidelines
| Property | T6/T651 State | T7451/T7651 State | T7351 State |
| Corrosion Resistance | Poor; requires full surface protection | Excellent; resists stress/exfoliation corrosion | Best; suitable for marine/salt spray environments |
| Weldability | Not recommended (high hot cracking risk) | Not recommended | Not recommended |


Leave a Reply
Want to join the discussion?Feel free to contribute!